+1
Regards,
Jordi
-----Mensaje original-----
De: ietf <ietf-bounces(_at_)ietf(_dot_)org> en nombre de "tom p."
<daedulus(_at_)btconnect(_dot_)com>
Responder a: <daedulus(_at_)btconnect(_dot_)com>
Fecha: viernes, 17 de febrero de 2017, 13:46
Para: <otroan(_at_)employees(_dot_)org>, james woodyatt
<jhw(_at_)google(_dot_)com>
CC: <draft-ietf-6man-rfc4291bis(_at_)ietf(_dot_)org>, IETF-Discussion
Discussion <ietf(_at_)ietf(_dot_)org>, <6man-chairs(_at_)ietf(_dot_)org>
Asunto: Re: Last Call: <draft-ietf-6man-rfc4291bis-07.txt> (IP Version 6
Addressing Architecture) to Internet Standard
From: <otroan(_at_)employees(_dot_)org>
To: "james woodyatt" <jhw(_at_)google(_dot_)com>
Cc: <draft-ietf-6man-rfc4291bis(_at_)ietf(_dot_)org>; "6man WG"
<ipv6(_at_)ietf(_dot_)org>;
"IETF-Discussion Discussion" <ietf(_at_)ietf(_dot_)org>;
<6man-chairs(_at_)ietf(_dot_)org>
Sent: Friday, February 17, 2017 7:44 AM
> James,
>
> 4291:
> For all unicast addresses, except those that start with the binary
> value 000, Interface IDs are required to be 64 bits long and to be
> constructed in Modified EUI-64 format.
>
> 4291bis:
> IPv6 unicast routing is based on prefixes of any valid length up to
> 128 [BCP198]. For example, [RFC6164] standardises 127 bit prefixes
> on inter-router point-to-point links. However, the Interface ID of
> all unicast addresses, except those that start with the binary
value
> 000, is required to be 64 bits long. The rationale for the 64 bit
> boundary in IPv6 addresses can be found in [RFC7421]
>
> Proposal:
> IPv6 unicast routing is based on prefixes of any valid length up to
> 128 bits [BCP198]. However, as explained in [RFC7421], the Interface
ID
> of unicast addresses is generally required to be 64 bits in length,
with
> exceptions only provided in special cases where expressly
recognised
> in IETF standards track documents.
>
> I think that's a good proposal.
> Perhaps with s/is generally required to be/are/
Ole
I would go further on the grounds that this is still somewhat woolly. I
would say
Proposal':
IPv6 unicast routing is based on prefixes of any valid length up to
128 bits [BCP198]. However, as explained in [RFC7421], the Interface ID
of unicast addresses is required to be 64 bits in length; any
exceptions
must be specified in IETF standards track documents.
It would be nice to have something IANA-like with different categories
of what can update what, with this being at the higher level, the bar
set higher for an Interface ID that is not 64 bits in length, but when
we say 'standards track' we are calling for IETF consensus and IESG
approval and it is hard to see what more could be called for, unless we
say that this is architectural and so the IAB must approve it!
Tom Petch
> Best regards,
> Ole
>
>
**********************************************
IPv4 is over
Are you ready for the new Internet ?
http://www.consulintel.es
The IPv6 Company
This electronic message contains information which may be privileged or
confidential. The information is intended to be for the use of the
individual(s) named above. If you are not the intended recipient be aware that
any disclosure, copying, distribution or use of the contents of this
information, including attached files, is prohibited.